BS 5480-1990
|
ID： |
EEEE919D8EF4445C006E7E1CC34206C7 |
|
文件大小(MB)： |
0.51 |
|
页数： |
54 |
|
文件格式： |
|
|
日期： |
2013-6-23 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS 5480:1990,Specification for,Glass reinforced,plastics (GRP) pipes,joints and fittings for,use for water supply or,sewerage,UDC [628.143 + 628.24]:621.643.2:678-462:678.017.3:678.03.067.5(083.3.71):006.3/.8,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Thu Sep 14 11:16:08 BST 2006, Uncontrolled Copy, (c) BSI,BS 5480:1990,This British Standard, having,been prepared under the,direction of the Plastics,Standards Policy Committee,was published under the,authority of the Board of BSI,and comes into effect on,29 June 1990,. BSI 08-1999,First published as BS 5480 in two,Parts:,BS 5480-1 July 1977,BS 5480-2 October 1982,Second edition as,BS 5480 June 1990,The following BSI references,relate to the work on this,standard:,Committee reference PLM/9,Draft for comment 89/38300 DC,ISBN 0 580 18320 3,Committees responsible for this,British Standard,The preparation of this British Standard was entrusted by the Plastics,Standards Policy Committee (PLM/-) to Technical Committee PLM/9, upon,which the following bodies were represented:,British Board of Agrément,British Gas plc,British Plastics Federation,British Plumbing Fittings Manufacturers’ Association,British Valve and Actuator Manufacturer’s Association,Department of the Environment (Building Research Establishment),Department of the Environment (Construction Industries Directorate),Department of the Environment (Property Services Agency),Department of Transport,Electricity Supply Industry in England and Wales,Engineering Equipment and Materials Users’ Association,Health and Safety Executive,Institute of Building Control,Institution of Civil Engineers,Institution of Gas Engineers,Institution of Production Engineers,Institution of Water and Environmental Management,National Association of Plumbing, Heating and Mechanical Services Contractors,Plastics and Rubber Institute,Plastics Land Drainage Manufacturers’ Association,Royal Institute of Public Health and Hygiene,Society of British Gas Industries,Society of British Water Industries,Water Companies Association,Water Research Centre,Water Services Association of England and Wales,The following bodies were also represented in the drafting of the standard,through subcommittees and panels:,Association of Consulting Engineers,Federation of Civil Engineering Contractors,Institution of Mechanical Engineers,Pipeline Industries Guild,Amendments issued since publication,Amd. No. Date of issue Comments,Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Thu Sep 14 11:16:08 BST 2006, Uncontrolled Copy, (c) BSI,BS 5480:1990,. BSI 08-1999 i,Contents,Page,Committees responsible Inside front cover,Foreword iii,1 Scope 1,2 Definitions 1,3 Materials 3,4 Pipe design limits 4,5 Dimensions 5,6 Classification 5,7 Physical properties 6,8 Performance properties of pipes 6,9 Fittings 7,10 Joints 7,11 Marking and information 8,Appendix A Method for determination of initial longitudinal unit tensile,strength by a tensile strip test 10,Appendix B Method for assessing initial longitudinal unit tensile strength,by a beam test 11,Appendix C Method for determination of initial circumferential tensile,strength by a burst test 13,Appendix D Method for determination of initial circumferential tensile,strength by a split disc test 14,Appendix E Method for determination of long term circumferential tensile,strength 16,Appendix F Methods for determination of strain corrosion resistance of,pipes 19,Appendix G Method for determination of ovality of a pipe after allowance,for distortion by its own mass 23,Appendix H Method for determination of initial specific stiffness and,resistance to structural damage under ring deflection 24,Appendix J Method for determination of impact resistance 27,Appendix K Method of test for leaktightness of pipes and their joints by,hydrostatic pressure testing 29,Appendix L Method for determination of long term specific ring stiffness,and creep factor under ring deflection 29,Appendix M Methods of test for leaktightness of flexible joints 31,Appendix N Methods of test for leaktightness of rigid joints 36,Appendix P Method for statistical analysis of long term data from GRP,pipes and fittings 36,Appendix Q Guidance on quality control testing and associated sampling 42,Appendix R Bibliography 46,Figure 1 — Dimensional boundaries for effective length and,out-of-squareness of nominally straight pipe 2,Figure 2 — Strip test piece for determination of initial longitudinal unit,tensile strength 10,Figure 3 — Diagrammatic representation of apparatus for the beam test 12,Figure 4 — Split discs and split ring test piece 15,Figure 5 — Diagramm……
……